When repairing machinery, you will frequently find that some bolts are exceptionally difficult to remove.The traditional solution to this problem has been to apply a flame to the bolt, which will loosen it, but this method is both dangerous and time consuming.With today’s, inefficient parts remove can seriously erode your profit.The sooner vehicles can be repairs begun, the sooner you start making money.
HBR012 is a flameless tool that can quickly and easily loosen rusted-on bolts.
1. The Heat Induction technology used is flameless, safe, and environmentally friendly. It greatly reduces the risk of accidents and potential damages.
2. Works in thirty seconds without damaging either the bolt or the surrounding equipment.
3. Easy to use, can be mastered in only 3 minutes.
4. Comes equipped with two LED lights, for use in tight spaces.
5. Choose from multiple coils, each suited to different type bolts.
6. The size of two books, it’ ll save you space and capital investment compared to flame-based tools.
7. WOYO Heating-Bolt-Remover is not limited to use on cars, farm equipment, boats and tanks, it is well suited to any machine repair job.
Input Voltage：12V
Input Current：40A
Output Power：500W
Output Voltage：40V
Output Current：120A
Packing List：
HBR Main*1
Jumper Cables*2(2.5m*1 0.5m*1)
Flexible Soft Coil*1（1m）
18mm coil(diameter of bore)*1（Length 20cm）
22mm coil(diameter of bore)*1（Length 20cm）
28mm coil(diameter of bore)*1（Length 20cm）
Package Size:39x33x12cm
Package Weight：3.5 Kg
Heating Bolt Remover Operation considerations
1. to prolog your heating inductor, leaving an 10mm air gap between the coil and the work piece is recommended as the insulation of the coil will eventually burn through if held directly to hot material.
2. Choose the appropriately sized coil to give the closest fit to the work piece.
3. Insert both ends of the coil into the coil location socket and tighten the thumb screws securely.
4. Activate the power switch to run the heating inductor for 1-3 minutes until enough heat has been applied to the work piece to break the rust/corrosion bond.
5. Release the power switch to turn off the power.
6. Do not use portable generators. The unstable voltage will damage the unit.
7. Turn unit off and allow the unit and all attachments to cool for at least 20 minutes. Handling the unit or parts before they have cooled may result in injury.
8. Make sure the unit is turned off and unplugged. After cool enough, use a dry, clean, non-abrasive cloth or paper towel to remove grease, oil, and other dirt from the heating inductor and electrical lead before returning them to the storage case. Storage of unit while still hot may result in damage to equipment or pose a fire hazard.
Tool Safety
1. Before plugging in the heating inductor, make sure that the outlet voltage supplied is compatible with the voltage marked on the label and within 10% of the stated voltage. An outlet voltage incompatible with that specified on the label can result in serious hazards and damage to the heating inductor.
2. Ensure attachment is securely located. Coil and main are firmly tightened before use.
3. Do not use the heating inductor for longer than the stated duty cycle: 5 minutes on followed by 5 minutes off. The main circuit board has an overheat protection device, however the attachments do not have overheat protection so should not be used for more than 5 minutes of continued use.
4. Please ensure that the cooling fan is running when the power switch is operated, if the fan does not run DO NOT use the heating inductor.
5. Do not attempt to create more than 4 coils when using the flexible soft coil, a minimum of 2 coils and a maximum 3 to 4 coils is the optimum number needed for best operation.
6. Do not leave the coil plugged into the HBR mains when not in use.
7. Do not attempt to repair the HBR by yourselves.
Reviews
There are no reviews yet.